blue-narchy ...
[ style:theme-default]


TECHOTSUKUMOGAMI
Edit here

Table of Contents
1 Mandatory introductory
2 PLANNING
3 WATER FLOW - 
4 DONE
5 FIXINGS TIPS 
6 ELEMENTS
6.1   > motor
6.2   > mast -o- don't
6.2.1       base:
6.2.2       mast:
6.3   > electricity
6.4   > chauffage [HEATING]
6.5   > zodiac boat
6.6   > PEOPLE WHO WANTS TO HELP
7 BOAT LOG
8 TRIPS & EVENTS
8.1   > MAPS
8.2   > METEO
8.3   > CREW
9 ADMINISTRATION
9.1   > need a boatname 
9.2   > Herstory
9.3   > Model
9.4   > Port
9.4.1       other
9.5   > BRYC access
9.6   > Permits
9.6.1       radio examen
9.6.2       zeiljacht examen
10 LOG (2018)
11 TOOLBOX
11.1   stuff to take
11.2   stuff there:
12 PROJECTS
13 FINANCES
14 where
15 CONTACT
16 SHOPS



Mandatory introductory
    - "Hold Fast" (1h15min): https://vimeo.com/15351476
    - Ten bullets:  https://www.youtube.com/watch?v=49p1JVLHUos



PLANNING

C H A N T I E R C O L L E C T I F
__________________________________
We meet each wednesday or maybe we are going to switch to Monday ?/?
We try to meet regularly - info@ooooo.be or check petites singularités


December 2021
November 2021
residency Caroline profanter 
install charger converter/inverter
Oktober 2021
September 2021

June2021
test motor 20june ok
test motor 07june ok
test sails - check the hook for tourmantin 
plumbery - still to put collier de serrage + maybe change the tubes? there is a weak point that is for sure! we can't get tube off nor put it on without dripping - best to do when on the dry dock?

April 2021
Install electricity and lamps/lights in the boat
- prepare electricity panel
 ( semi sprayed to make look fresh, holes are bigger but maybe needs adaptation if we order specific gear)
- replace rotten board to create a table for the electricity board OK if dry
- draw tech plans NEEDS REVISION _ptr looks at it. discussed a little with kurijn.
- to order equipment to finalize electricity setup


May/JUNE/August/Sept 2021

Wind generator ?! Test and make
To sail 
ALL pulley's are in the back cockpit in an old toolbox with a pulleay sign on it)
sails are at _ptr's place
- metal traveller - main sheet
- side jib rails
- transport sails (jib, genua, main)
- attach cleed BB front
- attach front cockpit hallyard BB jib
- attach cokcpit main halyard main sheet

A gearbox 
To not have the inside stick to switch - we keep the stick inside as second option in case of emergency) 
- check  cables? length ?
- check  pulley - we need 2? to make the corner ? to attach it to the motor
_ptr wants to move the gearbox ** because than we don't make a corner. ** but where?  ooooo likes more to keep the system but doens't realize whether it is practical for navigation if the speed of motor is in the inside of the window. test with lyn - an accelaration system + switching gears would be easier  ( front)


Resources to get ready ***
WATER FLOW - 
- sink system / new tubes +  connection pieces
- pump system
water tank : https://www.seashop.be/16658-en-flexible-drinkwater-tank-triangular-120l-105-cm-x-115cm-x-25cm&categories_id=327


This monday 29 june 2020
Guy will give us the wooden plank in oregon  for the deck 
   (option of iroko or teak but not possible for Guy to plane it)
>>>>PIETER can you go and get it monday late afternoon-night? because we leave with buratinas this monday 


from that to 16-17 july 2020
we will check how to put away the metal cables and take pictures
move forward to get comparative prices for these cables. 
by asking around we know that it takes a least two weeks for receiving the cables.
 kompas in  ostende
 barrois in vilvorde 

around mid july: need to adjust with our agendas
depending on progress
    to put the mast on trestles (check with Alain if ok?)
    we have the cables orwe dont and we still need to remove and order it 
   

from 10-15 August 2020
depending on progress
    we fix the deck-put the wooden plank-glue it with epoxi- put fiber glass-sand (multiple operations on the deck and ceiling)
    we fix the concrete on the floor
    we cut the inside beam for the plank to pass in 
    we fix the plank on the floor (epoxi-fiber glass)
    we drill holes to fix the mast base
    we fix the inside beam to the wall 
    we rectify the mastbase twist
    
    Teflon smeren  >> isolerende pasta (inox-aluminium) + Salpeterzuur fosforzuur Pasta

 we  clean the mast from electric cables, lights + fish 1 cable through for the top
    we remove the spreaders - find a solution for this job: https://dejond.com/nl ( i asked price for 150 30x2m)
    we adjust the metal base - ask help of Marc (grey hair and glasses) !!!
    we remove the paint - sand the mast (different sand papers 80>200)  - degrease (alumu prep: removes alodine) 
    and  first coating ? (Iridite and Alodine) than paint (??) (NO painting)
        
16 August 2020
    Accueil - open days at the collaborative-collective (which word to use ?) werf at BRYC 
                  - introduction to the others for the mast-antenna 
               ........ (promotion on that?which medium?when to communicate on it?)
                        (to let know BRYC)

17-21 August 
depending on progress
     continue the works above
     finish the mast spreaders-cables-electricity-antenna-lights-remove paint-reflector
     let's put the mast on the boat


to think about
VHF Martino? or we find another one?
to let know Bryc about this event 
shopping-catering 
shopping for construction works (concrete?screws....)

a list of tools that we will need
- sanding machine 2 ( oooo hs a new one!)
- electricity cable - extra
- discuese
- cloth for cleaning with products (bad tissue)
- protection gear - masks
- metal spinches brushes
- sanding paper
- revetten machine
- spray -paint - device -  make template to integrate  figurative forms
- gfrc cimont with fibers - or just add fibers to normal ciment
- mixer
- drill
- bucket ?
- camping gaz  (exchange bottle) : https://www.campingaz.com/
VAN CUTSEM
MEERWEG 45
RUISBROEK (BRAB.), 1601, BE
02/377 60 81

22 August
depending on progress
     preparation for the event 
     
     
23 August POSTPONED TO 20 SEPTEMBER
depending on progress
    event - radio listening session?
                we move the boat until the Club House, we transmit something and people are on the pier with their radio to listen
proposal : Radio listening sessions: "Murder in Troubled Waters" by Alice Lemaire is a documentary fiction series for radio, about a crime committed in the channel area. The series was made with residents of the Brussels canal area. The radio system and technical facilities will be developed during a 'collective shipyard'

---- just a though about this proposition, the staycation is in nederlands and this documentaire is in french (i think) so maybe we need to find something more convincing for this subsidy.
also i never listened this documentaire or contacted this Alice. 
  



a list of technical equipments for the event 


in the dossier : think about covid-time, we need to ask BRYC how much does it cost to moor at the clubhouse, as member do we ask for the clubhouse (on the website, it's writen that is free:)

---------------------------------------------------------
buy / radio https://www.icom.co.jp/world/products/marine/mobile/

Deck

DONE

(style) strikethrough - deletes the previous items:
    > go to edit mode to see what has been done
    (And in the styled document it disappears)

1st of april 2018 : boat needs to be off the yard & in the water..
- motor running
- basic electricty (nav.lights, radio)
- name for boat, insurance, vlaggenbrief (immatriculation)  
- rudder
- through-hulls inspected, eventually replaced
fetching sails (3) & pulleys from saint-gilles (rue glaciere neighourhood) & store it in PEL46 or S14 (ptr_ got contact details) 
-- 3 zeilen dacht k + hoop dat ie de schoot (l'écoute) & voorschoot ook liggen heeft
gustave desmed 31 saint gilles 1060




FIXINGS TIPS 

> people: Tips from Falko, Norway / falko89@gmx.net
Nausicaä, albin delta 31 feet, vetus deutz dt 14ltp , bermuda rigg

> Book
'boatowner's mechanical and electrical manual' by Nigel Calder 
https://www.abebooks.fr/servlet/SearchResults?n=200000021&ds=20&sortby=17&kn=Boatowner%27s+mechanical+and+electrical+manual.&cm_sp=pan-_-srp-_-loc

> youtube channels
https://www.youtube.com/user/madsdahlke
https://www.youtube.com/channel/UCg-_lYeV8hBnDSay7nmphUA
https://www.youtube.com/user/boatworkstoday
https://www.youtube.com/user/submarineboat

> mailinglist: 
SEAWOMEN - mailinglist : https://seawomen.noblogs.org/




ELEMENTS

  > motor
* alternator(HITACHI)  ____ Lila can help !
* regulator (TLIZ-51 12volt 503 HITACHI)
- empty - clean + aceton -  paint hull inside - danboline (pot with ptr) - vacuum    OK
- buy (seashop ou plaisance) + connect exhaust +  tubes      TODO (friday syphon vetus)
- cooling water cooling intake 
- silent block motor - adapt  / find solution with - recup old ones + pieter ones
- motor paint -  ? - 
* silent blocks
 original brand : PAULSTRA  (alternatieve merken, allpa, vetus,...)
 tussenafstand boorgaten berceau 92mm  
 draadstang montage motor M10
 hoogte demper : 35mm (moet onder 40mm blijven.. liefst minder)


  > mast -o- don't

      base:

- fix base + fill plate+epoxy deck
- beam - cleanup & - cut    (foot is still in place, removing it would need some cutting (wood)  
- in wood
    - pull out old foot
    - 2 or 3 beams (6x15cm+-) 
    - interior foot / top-plate
- metal 
   - new top-plate
   - weld-up the tube
   - reposition foot / secure it in place

      mast:
- adapt baseplate rotating mechanism (got fck when we took mast down last year)
- measure & rebuild spreaders / aluminium or a tube in the tube and solder (can be wood?) (pic with tube mesures)
- check inox cables 
- masthead lights  / anchorlight 
- emplacements for flag-ropes & rope for radar-reflector
- FOUND VHF antenna + cabling 
- wind vane / anemometer
- inspect pulleys  
- find lines & set it all up
-install antenna
-install reflector
-buy/search mariphone - vhf
- (ooooo's =done) load baofeng - vhf codes :  https://chirp.danplanet.com/projects/chirp
- install mariphone
-rope 9mm

  > electricity

- solar panel ?
- alternator /electricity 
- deepcycle gell batteries -
- eolienne - aerogen
-24 V> 12 V dc convertor

EXTRA - not bought
https://www.amazon.com/AiLi-Battery-Monitor-Voltmeter-Motorhome/dp/B07CTKYFTG/?tag=smartrvingnet-20
https://www.amazon.com/MICTUNING-6-5-100V-Digital-Voltmeter-Multimeter/dp/B01JOUZELG/?tag=smartrvingnet-20
https://seamarknunn.com/acatalog/nasa-clipper-bm-1-battery-monitor-12v-100-amp-8023.html
https://bullibattery.de/produkt/lcd-batterie-computer-100s-smart-shunt-1263/
https://bootaccessoiresvinkeveen.nl/progs/artikelinfo.php?id=146276
one piece of BMV702 is: USD49.43PC+USD15.06(Epacket freight to Belgium)=USD64.49
https://www.fangpusun.com/bmv700-702-catalogue

  > chauffage [HEATING]
  - install wood stove
  https://salamanderstoves.com/product/the-hobbit-stove/
  https://cubicminiwoodstoves.com/collections/grizzly-cb-1210/products/cb-1210-br-cubic-mini-wood-stove?variant=1331904548


  > zodiac boat
  - 2 old zodiacs & ptr_s need patchup glueing
  - zodiac of Tim & Go



  > PEOPLE WHO WANTS TO HELP

Tim- go - Juliette - Katja - benja-andrea-june-sophie/jérome 
Pascale-Julie(pote cabiria et son pere à un bateau au portugal)
Lila (radio+alternator) + Camy - rencontre un peu bato - bretagne may 2020
Arthur Passerina

PEOPLE TO CONTACT FOR THE MOTOR YANMAR
- Sophie
- Cabiria-julie 
- oncle Mira
-...

PEOPLE WHO HAS BOAT 
Veronique Santerre- cours gmdss - voilier ostende
seconde main vhf- Jean cours gmdss (vers mai-juin 2020)
Elisabeth (friend Katja) - Amsterdam - waarship
Mathias (friend Pieter) - Brugges
Gerda - Ouisquercq - tenace boot
Christophe Rault - écluse Ittre - Mima
Nat - Ouisquercq - Elizée
Mia et Goedele - Haru - Shetland sealark ( BRYC) 
Marie-Therese Schat - petite folie (little siling boat BRYC)

david from totalism.org (CHT)



BOAT LOG



<--------------------- (now)(new) BOAT LOG

2020
WINTER
- electricity wiring
- regenerate motor - STARTSTOP
- reverse troubleshooting alternator

2021
SUMMER
mast


APRIL 20
fill hole mastbase!
hole rudder (when boat outside?)

december 19
wintercheck with Martin

august 19
mastfoot inside 

september april :  mei-juni-juli > prêt a voil - end july - end august /CCC camp : https://www.zehdenick.de/index.html


April 2019:
    In Port of ANTWERP for "networks with an attitude"
    together with "FLOATING POINT"

sun  13- mon 14 jan 2019
- clean the bilge (vacuum ftw!)
- sanding  & painting bilge/motormount (danboline paint)
- cut out mast-base
- vacuum clean boat
- discuss dossier mobilite bxl
- search silentblocks (plaisance)
- get outboard motor back (entretien moteur @plaisance, 70EUR)
- removed a lot of tools 
- remove batteries & motor buratinas 

01.01.19 motor 
25.12.18 motor ptr_ and paolo clean and antirust paint
30.11.18 motor revision+clean (motor didn't start / maybe still  too much air inside)

?.11.18 motor revision
-------------
02.11.18 at the crane for the mast 
03.11.18 motor yanmar in the living


~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~


TRIPS & EVENTS
https://pad.constantvzw.org/p/techotsukumogami-trip
---------------------------
Arrival 06.10.18 at BRYC after 6 days of trip
---------------------------
BAPTIZATION  01.10.18

  > MAPS
https://www.unece.org/fileadmin/DAM/trans/doc/2013/sc3wp3/AGNP2013-v3.pdf

  > METEO
http://yachtingmerelbeke.be/getijdentabelmerelbeke.html   (not yet for october...)
https://www.waterbouwkundiglaboratorium.be/sites/default/files/atoms/files/getij_Wintam_2018_TAW.pdf
http://www.yachtweb.be/yachting/tij/2018/win%2010%202018.pdf
https://www.waterinfo.be/default.aspx?path=NL/HIC/GetijverwachtingenPopup&   (small graph of tidal situation for the coming days)


  > CREW
ooooo
alice
ptr_
...
tim
go


ADMINISTRATION

? >> april 2018
IMMATRICULATION
VLAGGENBRIEF
33.5 AV.net
33.5 ooooo
33 _ptr
%

  > need a boatname 
- ned ludd
- cimelody-3
- divine
q8
coca-cola
- pink flamingo 
- john waters
- soliton
sourire avant mourir  [sam ; original name]
- techo - tsukumogami   https://en.m.wikipedia.org/wiki/Tsukumogami    ****
- wd-40
- ...
- original name on safety-buoy: NINA2 (nieuwpoort)



  > Herstory
Admiral (Sam)
after a blueprint of Beeckman ? do we have the plans?
Guy Francois (Le Chien Vert)
where was the warf - waremme? or wemmel?

pics of boat (end of oct)
https://framapic.org/gallery#oiA072TqY6rP/4ZBCWenUvqsu,1Hf8Ea4fwFNA/ets6fZ91KXNO,g56cAUKOsulI/B9Ow2tlEQ9N2,42A2kafj9AeR/Yrt044jNfFML,NLi4Oo4rnu8O/qOxGBrxv2zKC,


  > Model
  TYPE???? Admiral 31 
  
saw same type of boat 'in the wild'
-one in Snef Yachting in Seneffe - 'Northern Star' / previous owner was in Landelies and second owner in Bruxelles-- will go to the trash, possible to take ladder- support for the mast - contact Patrick (harbormaster Seneffe)- )0475/643621
https://framapic.org/gallery#0govonrAXCnL/3mbSDTuhuntT,blYCDs7heyCF/1BZLIhC2xMNQ -- harbour 'luchtvaart' - portus novus corner to lombardszijde
- also one in brussel bryc (dock D)
- also 'black pearl' in nieuwpoort on the dry (portus novus vvw)  https://www.2ememain.be/bateaux/bateaux-%C3%A0-voiles/voiliers-%C3%A0-cabine/zeiljacht-admiral-31-446748674.html
- just saw (30 march 2018) another one on the dry in lombardszijde
-http://voilierjaune.over-blog.com/article-voilier-9-40m-a-vendre-8500-euro-124488211.html
-also 'Sud' in Ostende 


  > Port

currently : port of brussels

location: 
    watersportlaan, nieuwpoort
    the little green flag on this map : https://framapic.org/kRfNagexpDWk/nd9FZ8bpWPjK
    closest tram (coastal tram) is 'nieuwpoort stad' - 10min walk
    tramstop 'lombardzijde YMCA'  is also an option, bit longer walk, tried it, nice walk - but part is bit off-road 
    buses 68 & 69 also stop there (nieuwpoort stad) --  going from oostende station  (didn't try these yet)

      other
- lobroekdok ? close to atelier rooftoptigers, needs the ok of 'Antwerp Port Authority' i guess  (or get in the harbour, as for going to schelde-rijnkanaal & having a motor malfunction :-/ )
- grimbergen boatclub ?
- bermuda - access from south-east otherwise you get stuck in the reef :-)  got the map : https://framapic.org/7DCca4c4UTgy/lx7YXlhBFpWm

march: bring boat inland through canals (ganzepoot nieuwpoort, meest linkse sluis, plassendale-kanaal naar plassendale ( +- oostende), vandaar naar brugge (kanaal gent-oostende), dan door naar gent - vandaar schelde (boven-zeeschelde) tot rupelmonde en dan naar brussel (brussel-willebroek) of antwerpen (schelde)

- just to keep in mind :-/ destruction of boat : +- 1000EUR if done by VVW (local sailboat club)


  > BRYC access
- extra access-cards from nadine(caroline) /  ptr_  (20eur pp)

  > Permits


      radio examen
      18january20: lecture GMDSS in BRYC --- AVnet has the certificate ----waiting for the exam
  - marifoon VHF  (base exam)  https://www.bipt.be/en/consumers/radio/maritime/certificates-exams
    (use of digital protocols needs GMDSS license i think)
    https://www.ibpt.be/fr/consommateurs/radio/maritime/certificats-examens/manuel-vhf-maritime-version-2011

      zeiljacht examen

2019 autumn 
- dutch french course



log

somewhere september:
- mount rudder ( dig a hole in the ground +- 50cm...) : around 16 aug i got my big drill -- normally there are no cables running in the ground (asked the harbour office -- they are ok with these activities, as long as we close up after)
- repair keel/propeller (been digging a bit to let water out...)
- setup motor mount (welded some inox tubing)
- test the motor from trudo ( need tank, check general yachting http://www.gyc.be/ for Mercury motor gear...)  fail..
plan for mid august (before leaving for the trip to bxl):
- basic electricity (bilgepump, lights, radio?)
- finish up the hull  (do polyester job on propeller, finish it up with epoxy, apply  polycon on keel & antifouling on whole hull)
- mount rudder (dig hole in the ground, fit it in)
- setup motor mount (& a way to make it manageble underway -- would be great to be able to 'easily' control throttle & reverse)
- scheepvaartloket administration (ownership, name of boat, motor serial)
- put the thing on the water & make sure it floats > 1 OF OCTOBER18

Plan for septembre18
-finish the mount of the motor
-pass to this shop in Molenbeek to buy the stuff missing for the motor
-anode??
-lettrage name on the boat +immatriculation on the boat
-paint water line?
-finish to sand the propeller

-insurance  !  OK
-map
-papier boat + copy (ask what does it mean 'habitable')
-campingstove (ptr?) oops
-savety jacket  ('PFD')

1st octobre - 15:00
TechoTsukuMogami on the water
-last painting under the bloks?primer+antifouling?
-give back the mzmber card -- not done yet i did? or still in my wallet? ) ask


Think about :
-toilette 
-eolienne
-solar panel
-window for the backroom
-eco antifouling? next year
-isolation motor
-isolation boat
-base of the mast
- opening entrance /


nov 2018:
    - marielena/oracle WAB event?
    - take the yanmar out ?  (remove the table and move motor there to check & invite ppl around for dismantling/fixing)
    - think about options for heating inside..
    - get the mast off deck (move boat to small crane, lift it off & store in shelves)

oct 2018:  
    - suzuki motor groot onderhoud : get it back to plaisance (rue metsys, schaerbeek) for entretien (mandatory after +-20h runtime)  (i took it off the mount already - ptr_)
    - rainwater-leak from boom traveller fixation holes, impossible to work on now...
    - there's some leak from deck above the kitchen, saw drips just right of kitchenstove (still...)
    - keep an eye on bxl mobilite call http://www.mobilite.brussels
   -  pass by nieuwpoort ( finish membership etc)
   - pass by bryc secretariat : fix ligplaats, copy of vlaggenbrief & insurance papers ; officially ask for a garage...
  - find new thermos..




LOG (2018)

1-6oct : did the trip from nieuwpoort to bxl
  - ptr_ bought outboard motor last-minute (suzuki 4pk  -- 1 cyl 4 stroke) +-1050eur
  - spent some nights in harbour (10eur p)
  - bought waterwegenvignet at wintam (40eur -- till march2019)


21-26 aug nieuwpoort workweek (ptr,ooooo,alice+inge,lize one day)
-cleaning the interior of the boat
-rudder mounted  (big hole that  we recoverded)
-mastic poliester +époxy+fiberglass around thé propeller
-replacing lights bâbord et tribord + changing bulb for the back ->led 
-electricity : moved mainswitch + lights + bildgepump
-cable + tube for the bildgepump
-first try for the mount of Mercurymotor outside but need some adjustments 
-sanded all the hull
-sanded the propeller
-painted the hull with primocon primer (one layer)/4h waiting + antifouling dark grey (two layers) wait 16h between the 2 layers
-demarches administratives pour lettre de pavillon et immatriculation ->payed & waiting for the papier (S14?)
-bought some stuffs in de kringwinkel ->knife,thermos,spones,
- pass by scheepsloket & start immatriculation process (4-6 weeks) valid for 5 years (147eur  sea/beneden-schelde + 147eur interior waterways B77638) 


8 aug 
- found a ladder  (hsbxl threw some broken gear out )


6 aug
- sanded the keel (seems there-s an epoxy layer on, so that-s fine for the moment, we'll do with some polycon & antifouling i think
- payed summer berth (290 eur, VVW)
- bought some fiberglass, aceton & 5mm bolts (26 eur fck..)
- hooked up an old battery charger (30 min +-) seems ok
- sanded up area where propeller axis exits keel-- was badly done, contained water, so sanded out & let it dry before treating with glassfiber/polyester & apply \watertight'
 

2-3 aug
- got nadine's old motor from storage (trudo-s)
- quick cleanup with isopropyl
- motor looks good
- drilled out part of sparkplug thread with 13mm drill (sparkplug is Ø 12mm  (somehow nadiners tried to screw in wrong sparkplug & killed the thread)  motorblock is aluminium
- bought sparkplug (ngk dcpr6e, 6eur @ OPA)
- mounted correct sparkplug ( only 1cm thread left instead of 2cm...) hope it doesnt blow out
- bought correct motor oil (17eur, plaisance)
- need tank... (will check for connector @ gyc.be)

end of july
- took back tools (were onboard for motor-entretien) --  back to bxl
- rudder is on board ( not mounted)
- took a bit of time to be depressed of the whole thing :-)

somewhere in june
- finished up rudder

9-10 may (ooooo ptr_)
- diesel pump manometer (hope it works ... nope)
- 12mm wrench to unlock injector.... (hope it works ... nope)

called shipsupport nieuwpoort - not open tomorrow (holiday)
but they are open friday & they have a test setup for injector

--

somewhere in april (ptr_ ooooo alice martin)
- replacing tubes for hotwater / diesel
- add fuelfilter
- check fuel highpressure side (seems ok, but let's test pressure next)
- throughhulls all done now
- ooooo put 420eur in the moneyjar(ptr_)
- car cleanup at the same time  :-) 

--

thursday 29-friday 30 march 2018 (ptr_)
- dismounted through hull near motor -- in ok shape (3.85cm diam) -- needs new valve, needs m4 bolts to mount back
- bought replacement pieces for motor (548.63eur)
- bought new through-hulls & valves (94.49 eur + 88.94 eur)
- bought some more sikaflex 291
- measured rudder mount
- line (rope) thickness 0.8cm - 1cm   (ordering 1.2cm at vidaxl ?)

- try to dismantle oilscrubber - didn't work (bolts loose, but no moving)
- found back bolts to mount exhaust elbow

all through-hulls are out, bought new one's ) -- 
* bakboord: 4.5 cm (1'1/4 - 4.2cm) -- old speedometer
* bakboord 3cm (3/4' - 2.6cm) -- kitchen outlet
* stuurboord 4.4cm (1'1/4 - 4.2cm) (toilet outlet)
* stuurboord 2.1cm (1/2') hole is not round, needs some rework (toilet inlet)
* stuurboord  3.25cm (motor coolingwater)
   -- needs small M4 bolts -- is ok : i put inox bolts in there, need to check in 5 years how they're doing :-)

replace motor tubing:
    coolingwater 1.3cm innerdiam +- 1m total length
    diesel 0.8cm innerdiam +- 0.5m (bought fuel filter to add)
    diesel 0.6cm innerdiam 0.25m (transparent, tank fuel level indicator)
    whale pump (bilge) innerdiam 3.85cm  2m length ?
    
rudder : measured tube length : 1m (99cm precise..)

-- 

friday 15-saturday 16 feb 2018 (paolo, ptr_)
- cut out through-hulls; all taken to bxl (measuring & replacement)
- extracted rudder & taken to bxl  (took it out from deck; this wont work for reinstallation but that's another problem)
- toilet taken from board  - cleanup & resell ? 
 - replaced motor oil (exactly 2L)
 

wednesday 13 feb 2018 (ptr_)
visit from steven & erik (contacts of ooooo) to have a look at the dieselmotor; 
among the things learned: 
    - compression valves can be disabled (needed for manual start; make speed handcrancking and then kick in the compression)
    - startmotor is working; 
    - change the oil before trying to run it, change it again after a first real run  (needs cooling system up and working...)
    - put in a diesel filter 
    - working of electric contacts of starter motor (white terminal to positive terminal: closes a relay inside and let power flow)
    - motor 'runaway' because of overfilling oil is almost always fatal (no speed  regulation, as the governor only regulates dieselfuel, but the oil is abundant...)

2018 jan 15-16: alice, ooooo& ptr_
- ALWAYS BE KNOLLING https://framapic.org/P7d8XiGztAnn/AoejXGOdKZ3j  https://framapic.org/bloTVcA4xKiy/VkZ8P2OQHoZK
- cleanup aft cabin https://framapic.org/9JRuNwCHJ3Eq/zCqH1oOpgadc 
- took out the manual pump (whale, s nice)  https://framapic.org/hdIueAqrbrmM/UtPoykY5n8LB
- took out diesel reservoir -- quite rusted underside, needs better inspection before put back in use (if so)
- dismantled mast base (inox plate on the deck)
- clean up rot under mast base https://framapic.org/MZ31f30RYwJy/9emqKwFRnkPX
- get a canister of diesel (+- 10L)
- take out the inox plate in cockpit  (probably there was a support under it, seems there's some rusted steel support platform inside)   https://framapic.org/mNRsC4snxNGX/e0vl3laTJSae
- found the genua in front cabin, took it to bxl (had small inspection, seems ok, didnt do any repairs)
- took toilet out, had to cut off the valves...  https://framapic.org/vYETd9f53Sis/AbGEJqV7pUri
- inspect valves -- took some to bxl for refurb, think i forgot them in ooooo car...S14? platic bag ?
- inspect through-hulls :  generally in BAD state -- most (all?) need reseating...
- cut off the rudder blade -- in bxl now -- axle is still stuck in place...


dec 30-31: ptr_
    - moved vacuum cleaner on the boat
    - have foldable bike on the boat
    - general vacuum cleaning
    - found the pulley system for the boom (still missing traveller)
    - did a cutout to make the passage to galley bit wider https://framapic.org/woplT0mhLQpv/kKFCLJ2CJeZd
    - dismantled door of toilet (to have better look & more workspace (rotten mast-support beam)
    - found an eberspacher diesel heating system in the bin, no clue yet if it will work
    - found more camping-gaz canisters for kitchen


dec 22-23-24 2017:  work weekend paolo & ptr
  *motor cleanup, 
    - dismantled exhaust (--> needs replace, ptr researching pieces)
    - motor is YSE12 (model number on gearbox)
    - cleanup - looking good
    - tried to dismantle cooling, all bolts are ok, but needs more research
    - zinc anode still there, but could use replacement
    - threw away the trashed pillows,fridge etc
    - next steps:put exhaust back, get diesel & oil,  run the motor (without cooling) for a quick test, replace oil
    * recup of teak from harbour...  (late-night operation :-)
      - nice to make benches in cockpit, we did a quick cut to replace the missing bench ftm
    * camping gaz cooker working 
       - there is camping-gaz shop in lombardzijde, near tramstop 'stad' (20min walking)
    * mast was falling sideways, replaced with sturdier woodconstruction.
       


early works:  (ptr_, paolo, ooooo, alice)
    - remove rotten wood in interior
    - remove other junk (shitty fridge, pillows)
    - discover leaks & try to close them on deck -- tape them off
    - take down mast & not touch other boats in the process...
    - mount table
    - gas stove for kitchen
    - remove crufty vinyl flooring everywhere
    - sanitize
    
-------




TOOLBOX

  stuff to take

<---------------------- (new) 



  stuff there:
- vacuum cleaner (general cleanup) ok
- disceuse ok
- bike (foldable bike in bxl) ok
-inox ! screws ok
- wd40  moar ok now
- kettingtakel (motor lifting)  not yet > in bxl
- more hex-keys (motor work)  +- is ok imho
- needle & thread  can wait
- good ductape  need this, will buy (ptr_)
- pipe-clamp (loodgieterstang)  ok
- heating/hot air blower -- ok (it eats elec though..)
- wooden beams to take the mast down  done without, better next time...
- vuilzakken (sac pour poubelles)  ok
- try hotglue for temporary waterproofing
    - viseuse
    - wipzaag
    - general toolbox with hex keys
    - small metal saw
    - cable cutter (small)
    - tec7   glue + pistol  (there's also sika 291)
    - power chord (+-40m) -- elec is +- 35meters away, need 1EUR coins (there are some on the boat) 
    - small shopping trolley 
    
---- 




PROJECTS

rotten mast base:  ( quite a big set-back..)
- found out the base of the mast (compression post) is rusted & rotten out  >>> need to bring mast down asap << done
- bring mast down https://www.youtube.com/watch?v=vpFhnYQmRYs   -- or better : https://www.youtube.com/watch?v=Wr6pvPkH6H0
- need wooden beams (gin-pole/A-frame), good rope & pulleys (katrollen)
[1 nov] mast takedown pics (stepping mast with ginpole  gone sideways.:-/  

https://framapic.org/gallery#R07iNkVsbvd2/7koT1r9A2moL,C9wzpy7RDiCc/S3lRWyApdl45,n9Ut28jvX1UE/zK98u4EfDklg,enPyG4JJtFyB/weSByomahYNy,rRtmAhKgtQVS/fr8t3XA10jRV,96lbmOUP2xsI/CgSsBv2pAJHe,ygZCHyNBn5Dn/vU63XIOWSQ6l,AcgXNNg36FbS/mgCryI3pb8iL,P7d9m1q4jvaO/XKQ7QFrRUYXO,uwF4mvHfDgMu/0VAbDA1c1rJa,XlXv01nb15PH/Ood53tPa8NNm,kfVUAn953kTB/6baPJ3DWRBpx,sMNLH8feySuI/xsKa2g78qhnT,FhdaWyOqBWZR/RR2tRaFn9Ysg,22tqltuXuHBa/iXqtqZlo4S1w,

- replace existing steel post + wooden support 
wooden beam to replace steel beam
need to check how to support on keel
 
found out keel-balast is in concrete -- i had a look online and doesnt seem an immediate problem, just not great...

motor:
- yanmar  YSE12 -- the good stuff
- simple motor (1 cyl), a lot of info online (hours of youtube videos of rebuilds etc) 
- needs a new exhaust elbow 
- needs oil sediment cleanup & oil flush & refill
- build system for throttle control from cockpit
- thermostat is not looking great
- found the driving belts
- youtube series of total motor rebuild  (YSE is earlier version of same motor)  https://www.youtube.com/results?search_query=yanmar+yse12+aussie50
- pics:
https://framapic.org/gallery#HBDCwJYXomVC/ziuBPaPrPpA8,X3e46TGoC53G/c8ACdCeZ2xcI,RIzCgvoVfKAz/bwR8ZHqV0q2J
22-23-24 dec: https://framapic.org/gallery#IK18oFKvgFpR/nXRunFNAscSF,l8D4yxI4Sjry/OR7ZCJtlDMFi,pIrVDBnU0Ujh/B6kAYoWlml9p,tEcAE587De6X/tGFeoiDeC7Yo,gFVwWI4MNXZw/HJw4VR932UOY and moar https://framapic.org/gallery#vzPXZo1JPDvf/h7MEGHTbHEes,UcNRMofNF2xX/JfnbVZTfYT9v,mon8Cnpeilda/CqJoZJR4o1Xw,JKw4lc07M4GC/gtK0w3XZFHyT,S69SDaMPKjTF/naRRppLw4ZHL,vraU6qVSqLr4/KYLt9AoAx8l5,1DSKsNDR5NXj/bepqgpdeO43N,nKHVm4Bnrc4K/9jugcqQhyFJs

electricity :
- battery (local dealer 120Ah : 152eur+tva / 100Ah :120eur+tva)
- i got recup cables from floatingpoint
- needs some planning

rudder: underwater rudder needs to be rebuilt... 
- dismantle existing rudder & recup pieces to build a new one 
- weld a new inox skeleton from recup'ed pieces 
- foamcore over skeleton ?  maybe light wood & sand down to shape?
- layer up polyester/epoxy for structural integrity
- gelcoat or epoxy for waterproofing
- called artois composites (oostende):dense foam material : PVC or PET
  they have an incoming order of PET 'blokjesplaat'  - perforated (so better adhesion under vacuum) plates 
  one plate is 122x122x2cm -- base price 51EUR btw inc


through-hull :
- probably need to replace them all (+-25eur pp)
- through hull bronze pieces moving in the hull, so ... replace...
lines & ropes:
- need to replace all running lines (all ropes)
- probably 3a400 eur i guess (may be cheaper in antwerp)
- mast is +-11 m high, made in aluminium
- we have to take down mast anyway so no need to replace ropes for now


radio:
    - martino has marine VHF radio in amsterdam still?  otherwise need to source one  2ndhand
    - sailmate vhf not working ftm (scored in bryc-poubelles)

hull bumper-rail
- wooden original bumper rail is gone, not structurally needed but it looks rather punk now

paint for hull
  - 1-2 days of sanding/cleaning
  - 1 day for painting 
  - easily needs 200-300 eur
  
deck:
    - could use some anti-slip  (there's a roll of nice material @ PEL46)
    - re-seating blocks for genua sheets (need to find suitable material for distance-holder first)

FINANCES

spreadsheet:
2020 
https://ethercalc.org/n6jt2dd105mc
2019
https://lite.framacalc.org/techotsukumogami%20financials

TO BUY

where
https://www.compas.be --- MARTIN, Tekla Norway want to give us one 
https://www.seashop.be/
https://www.bootaccessoiresvinkeveen.nl/progs/artikelen.php
https://www.toplicht.de/
lachoure/

- rescue boat (sales in plaisance)

- anti fouling  /   DONATION atelier marin
https://www.seashop.be/175182-en-antifouling-international-interspeed-ultra-eu-black-25l-ybb704
http://nordkyndesign.com/ultrasonic-antifouling-system/


http://www.finres-sa.com/contact/
- epoxy ? if so which one? http://www.finres-sa.com/produits/stratification/epoxy/
epoxy stratifie +  epoxy(?) schuim 
- fiberglass -- 2 vierkante meter

- ropes 
2xmastlengte + 5m  (take sample) (take katrol)

- inox cables
- mast spreaders? 
Traveller - 80 euro
https://www.toplicht.de/de/shop/decksbeschlaege/schiene-und-rutscher/sprenger-decksschienen-und-rutscher

- electricity (cables? LED?)

- special paint to re-do immatriculation ? 

- safety jackets ---> 4 on the boat (_ptr's ones?)
  https://www.seashop.be/c10-en-safety_lifejackets
  https://www.seashop.be/300679-en-a-red-handflares-1-piece-solas-f-4years-valid
  
- marifoon 
we wait till alice has license
https://www.hfelectronics.be/marifoon/antennes

- antenna VHF- marthe bought one 22€ doesn't work

- EPIRB/SART 
not necessary  & expensive

electrical system
  - battery cables
  - battery mounting 
  - general cables 
  

-knot meter? 
  
- gear shifting mechanism

 -anchor
  - rolsroyce  :  https://www.seashop.be/77106037-en-rocna-anchor-25kg




CONTACT
hervé +32 483 39 12 75 
Beeckman (bateau Samba BRYC) 
maynamike@hotmail.fr   pour histoire Admiral pont fait par beekman - 
32 bateaux ont été fait 
?
------

SHOPS
- exhaust.
http://www.leonsmet.be/
-la maison du caoutchouc
http://www.rubbercenter.com/
-https://www.chaput-caoutchouc-belgique.com/
- corderie barrois (on the road to vilvoorde before pont buda)
https://www.corderiebarrois.be/
- quincallerie . Droeshaut
https://www.pagesdor.be/entreprise/Molenbeek-Saint-Jean/L11264452/ETABLISSEMENT+DROESHAUT/
- cordage-cables
https://www.compas.be/




(Site generated by E2H, an "Etherpad hypermedia" project by @dcht00). Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.